ITI NIMI Mock Test Fitter 1st year 2023

ITI NIMI Mock Test Fitter 1st year 2023

आईटीआई (औद्योगिक प्रशिक्षण संस्थान) प्रश्न बैंक आईटीआई में पढ़ाए जाने वाले विभिन्न ट्रेडों से संबंधित प्रश्नों और उत्तरों का एक संग्रह है। आईटीआई व्यावसायिक प्रशिक्षण संस्थान हैं जो इलेक्ट्रीशियन, फिटर, वेल्डर, मैकेनिक आदि जैसे कई क्षेत्रों में तकनीकी पाठ्यक्रम प्रदान करते हैं। iti nimi mock test fitter

iti nimi mock test fitter आईटीआई प्रश्न बैंक में प्रत्येक ट्रेड से संबंधित सभी विषयों और अवधारणाओं को कवर करने वाले प्रश्नों की एक विस्तृत श्रृंखला होती है, जिसे छात्र अभ्यास और संशोधन के लिए संदर्भित कर सकते हैं। यह उन आईटीआई छात्रों के लिए एक उपयोगी संसाधन है जो अपनी परीक्षाओं की तैयारी कर रहे हैं, साथ ही उन प्रशिक्षकों के लिए भी जो परीक्षण और असाइनमेंट बनाना चाहते हैं।

प्रश्न बैंक भौतिक पुस्तक, ऑनलाइन संसाधन या सॉफ्टवेयर प्रोग्राम के रूप में हो सकता है। कुछ आईटीआई प्रश्न बैंक सैंपल टेस्ट पेपर, मॉक टेस्ट और पिछले वर्षों के प्रश्न पत्र भी लेकर आते हैं, जो छात्रों को परीक्षा पैटर्न और पूछे जाने वाले प्रश्नों के प्रकार के बारे में जानने में मदद करते हैं। iti nimi mock test fitter

कुल मिलाकर, ITI प्रश्न बैंक छात्रों के लिए उनकी ITI परीक्षाओं की तैयारी करने और उनके चुने हुए ट्रेड में एक ठोस आधार बनाने के लिए एक महत्वपूर्ण उपकरण है। ITI NIMI Mock Test Fitter 1st year 2023

ITI Fitter Objective Question & Answer :

1- Which of the following is not a measuring tool?
a) Vernier Caliper
b) Micrometer
c) Hammer
d) Height Gauge
Answer: c) Hammer

2- Which of the following is used for tapping internal threads?
a) Tap wrench
b) Die wrench
c) T-handle tap wrench
d) Adjustable tap wrench
Answer: c) T-handle tap wrench

3- What is the function of a reamer?
a) To drill a hole in metal
b) To widen a hole in metal
c) To cut external threads
d) To cut internal threads
Answer: b) To widen a hole in metal

4- Which of the following is not a hand tool?
a) Hack saw
b) Center punch
c) Power drill
d) Screwdriver
Answer: c) Power drill

5- Which tool is used for holding a workpiece while performing operations on it?
a) V-block
b) Drill bit
c) Countersink
d) Reamer
Answer: a) V-block

6- Which of the following is not a type of hammer?
a) Ball-peen hammer
b) Sledgehammer
c) Dead blow hammer
d) Torque wrench
Answer: d) Torque wrench

7- What is the function of a torque wrench?
a) To tighten nuts and bolts to a specific torque
b) To loosen nuts and bolts
c) To measure the diameter of a hole
d) To measure the length of a workpiece
Answer: a) To tighten nuts and bolts to a specific torque

8- Which of the following is used for holding a tap for tapping threads?
a) Die holder
b) Tap wrench
c) Adjustable wrench
d) Pin vise
Answer: b) Tap wrench

9- What is the function of a scriber?
a) To mark lines on metal
b) To cut metal
c) To drill holes in metal
d) To bend metal
Answer: a) To mark lines on metal

10- Which of the following is used for cutting threads on the outside of a cylindrical workpiece?
a) Tap
b) Die
c) Reamer
d) Countersink
Answer: b) Die

11- Which of the following is used for measuring angles?
a) Vernier caliper
b) Micrometer
c) Protractor
d) Depth gauge
Answer: c) Protractor

12- What is the function of a ball-peen hammer?
a) To tighten nuts and bolts
b) To strike punches and chisels
c) To cut metal
d) To drill holes in metal
Answer: b) To strike punches and chisels

13- Which of the following is used for holding a workpiece while drilling?
a) V-block
b) Tap wrench
c) Die holder
d) Pin vise
Answer: d) Pin vise

14- What is the function of a center punch?
a) To mark the center of a hole to be drilled
b) To cut metal
c) To drill holes in metal
d) To bend metal
Answer: a) To mark the center of a hole to be drilled

15- Which of the following is used for cutting internal threads?
a) Tap
b) Die
c) Reamer
d) Countersink
Answer: a) Tap

16- Which of the following is used for measuring the diameter of a hole?
a) Vernier caliper
b) Micrometer
c) Dial bore gauge
d) Depth gauge
Answer: c) Dial bore gauge

17- Which tool is used to hold the workpiece in a lathe?
a) Drill bit
b) Chuck
c) Hammer
d) Pliers
Answer: b) Chuck

18- Which tool is used to measure the internal diameter of a hole?
a) Vernier caliper
b) Micrometer
c) Depth gauge
d) Bore gauge
Answer: d) Bore gauge

19- What is the purpose of a center punch?
a) To make holes in metal
b) To mark a point for drilling or punching
c) To grip and turn small screws
d) To cut threads on a bolt or screw
Answer: b) To mark a point for drilling or punching

20- Which tool is used to tap threads in a hole?
a) Tap wrench
b) Center punch
c) Chisel
d) Screwdriver
Answer: a) Tap wrench

ITI NIMI Mock Test Fitter 1st year 2023